Screw oil presses
Retouched product visualization. Final configuration is subject to the approved technical drawing.
Screw oil presses / TECHNICAL PROFILE
VG-120D II
Screw oil press with optional filtration
A screw oil press with a stainless steel feed hopper, heated pressing assembly and accessible controls. The supplied rapeseed reference capacity is 260–400 kg/h. A separate vacuum filtration unit can be discussed as part of your project configuration.
SEED FEED RATE260–400 kg/h · rapeseed
MAIN DRIVE11 kW
DESIGNED AROUND THE DETAILS
Know your
configuration.
Final selection depends on your raw material and operating conditions. We confirm the complete technical scope before an order.
| Reference material | Rapeseed |
|---|---|
| Seed feed capacity | 260–400 kg/h |
| Main motor | 11 kW, 6-pole |
| Heater | 4 kW |
| Screw diameter | 120 mm |
| Screw speed | 49 rpm |
| Press chamber internal diameter | 121 mm |
| Overall dimensions (L × W × H) | 1890 × 980 × 1470 mm |
| Machine weight | 880 kg |
| Standard electrical supply | 3-phase 380 V / 50 Hz; confirm before order |
| Hopper & oil tray | 304 stainless steel |
| Optional separate vacuum filter | 10 L; 1.1 kW; 50–160 kg oil/h (temperature dependent) |
Feed capacity is not oil yield. Dimensions and configuration must be confirmed for the supplied machine.
MATERIAL FIRST
Match the seed.
Then size the press.
Use the VG-120D II reference data as a starting point, not a guarantee for every oilseed or process.
REFERENCE FEED CAPACITY
260–400 kg/h · rapeseed
The listed figure describes seed input, not finished oil output. Confirm the reference material and configuration in the specification table above.
- Share the seed variety, moisture information and cleaning or conditioning method.
- State your target seed input per hour and planned daily operating hours.
- Agree on material preparation and operating conditions before selecting the machine.
The available capacity references do not specify a complete test protocol. Exact moisture targets, conditioning temperatures and guaranteed output need confirmation for your material; no trial results are implied here.
OTHER OILSEEDS / PROJECT REVIEW
Discuss suitability before ordering.
For peanut, sunflower or sesame projects, confirm material preparation and model suitability with the equipment team. A rapeseed feed rate must not be reused as a guaranteed rate for another seed.
- Peanut: discuss shelling, clean kernels and conditioning.
- Sunflower: discuss variety, hull content and whether dehulling is appropriate.
- Sesame: discuss cleaning, conditioning and the intended oil characteristics.
Where performance is uncertain, request a material trial and agree what will be measured.
Read oilseed preparation guidesDEFINE THE SUPPLY SCOPE
The press.
The supporting equipment.
Separate the listed machine configuration from project-specific additions. Final inclusion is governed by the confirmed technical scope, not by a photograph.
LISTED PRESS CONFIGURATION
VG-120D II
- Main drive
- 11 kW
- Heater
- 4 kW
- Standard electrical supply
- 3-phase 380 V / 50 Hz; confirm before order
- Hopper & oil tray
- 304 stainless steel
The full table above remains the reference for the machine dimensions, weight and mechanical specifications.
OPTIONAL / TO BE AGREED SEPARATELY
Separate vacuum filtration
The separate vacuum filter is an optional downstream unit, not an automatic inclusion with the press.
- Listed filter reference
- 10 L; 1.1 kW; 50–160 kg oil/h (temperature dependent)
Filter throughput measures oil flow, not seed feed. Confirm the duty and operating conditions when matching it to the press.
Confirm seed preparation equipment, oil collection, filtration, commissioning arrangements and wear-part supply individually before an order. Filtration alone is not refining or proof of food-standard compliance.
Confirm the supply scope for VG-120D IIBEFORE DELIVERY
Prepare the site.
Plan the upkeep.
A procurement checklist, not an installation or operating manual. Machine-specific settings and procedures must come from the approved documents for the supplied configuration.
ELECTRICAL
Confirm your local supply.
3-phase 380 V / 50 Hz; confirm before order
Provide your phase, voltage and frequency before ordering. A different supply requires engineering confirmation; no alternate-voltage version is promised on this page.
Main motor power is not a complete site-load specification. Have qualified personnel confirm wiring, earthing, protection and the requirements of heaters and any auxiliary equipment.
LAYOUT & COMMISSIONING
Check access and working space.
Use the listed machine dimensions for initial planning, then request the approved layout and foundation or anchoring requirements.
- Check delivery access, equipment placement and ventilation.
- Confirm space for feeding, oil collection, filtration and maintenance.
- Agree on operator training and commissioning responsibilities.
No installation clearance or foundation design is specified here.
MAINTENANCE
Request the supplied manual.
Confirm cleaning access, wear-part identification, spare-part availability and the maintenance schedule for the supplied machine.
Isolate and lock out power before maintenance. Follow the actual machine instructions and use qualified personnel where required.
Lubricants, adjustment settings and service intervals are not specified in the available product references. Obtain these from the machine manual, not from a generic website checklist.
SUPPLIED PROCESS FOOTAGE
See the process.
Verify your configuration.
These supplied videos show pressing, oil collection and factory demonstrations. Exact model mapping and test conditions have not been confirmed; none is presented as a VG-120D II acceptance test or a capacity guarantee.
Seed feeding and oil-flow reference
Process reference only, not a safe-work demonstration. Do not copy adjustments around exposed moving or hot parts. Follow the supplied manual, keep guards in place and use trained personnel.
More supplied process videos
Pressing and cake-discharge reference
Factory demonstration reference
Installation and operation overview — reference only
For qualified personnel and model-specific review. The video shows an example configuration, including filtration. Do not apply its cable sizing, lubrication levels, temperatures, rotation checks or control sequence to VG-120D II without the approved manual and electrical drawings. Isolate and lock out power before wiring or servicing.
Supplied installation and operation overview
Existing sesame process reference
The model in the clip has not been confirmed; it is not presented as a VG-120D II performance test.
About the product images and model-specific evidence
Bundled product and component images are retouched visual references. They are not approved engineering drawings or evidence of wiring, safety compliance or the final supplied assembly. Request current, unretouched photographs and a model-confirmed running video when discussing your configuration.
YOUR PROJECT / VG-120D II
Send the details
that shape the selection.
The inquiry form will preselect VG-120D II. Include the following so the discussion starts with your process, not just a model name.
- Raw material, preparation method and available moisture information.
- Target seed input per hour and planned operating hours.
- Installation country, phase, voltage and frequency.
- Required filtration, oil collection and supporting equipment.
- Requests for the current configuration photos, model-confirmed video, manual and wear-part list.
A CLOSER LOOK / VG-120D II
The details behind
the specification.
304 stainless steel hopper
Controls in one place
Follow the oil flow
OPTIONAL / DOWNSTREAM FILTRATION
Pressing and filtration.
One coordinated scope.
The separate vacuum filter is optional. Use the current filter reference in the configuration section above; oil-flow capacity is not the press seed feed rate.
These retouched component images are visual references, not approved drawings or confirmation of the supplied assembly.
Discuss a pressing & filtration configuration ↗MACHINE HIGHLIGHTS
Practical by design.
01
304 stainless steel hopper and oil collection tray
02
Heat-treated 20CrMnTi screw and cage bars
03
Cr12MoV cake outlet
04
Accessible control panel
05
Machined welded support frame
06
Optional separate vacuum filtration
Continue exploring.
All equipment ↗Screw oil presses
Screw oil pressesTELL US ABOUT YOUR PROCESS
Choose your press.
Define your configuration.
Share your oilseed, required throughput
and installation country.